RESUMO As placas de circuito impresso (PCIs) são as partes mais valiosas dos resíduos eletrônicos, pois possuem uma considerável quantidade de metais com potencial de recuperação. Processos de reciclagem com o intuito de recuperar metais de PCIs têm despertado interesse ultimamente. Contudo, uma fração destes resíduos não é completamente aproveitada e tem destino incerto, como ocorre para a fração não-metálica e o pó gerados durante os processos de recuperação de metais. O foco deste estudo foi o emprego do pó gerado nos processos de cominuição mecânica, separação granulométrica, magnética e eletrostática de PCIs controladoras e indicadoras de temperatura de câmaras frias, para obter compósitos de matriz de polipropileno (PP) com diferentes teores de pó de PCIs, 5, 10 e 20% em massa. Os materiais foram pesados, misturados, moldados por injeção e posteriormente caracterizados por ensaios de tração, dureza Shore D, espectroscopia de infravermelho, análise termogravimétrica e microscopia eletrônica de varredura. Os resultados dos ensaios de tração e dureza indicaram propriedades levemente superiores às do PP puro, exceto para a deformação na ruptura, que foi reduzido em até 2,7 vezes para a amostra com 20% de resíduo. O desenvolvimento de compósitos utilizando o pó de PCIs se mostrou viável em aplicações onde as propriedades resistência à tração, rigidez e dureza são determinantes, mesmo para um elevado teor de resíduo (20%) agregado.

ABSTRACT Printed Circuit Boards (PCBs) are the most valuable parts of e-waste because they have a considerable amount of metals with recovery potential. Recycling processes aimed at recovering metals from PCBs have aroused great interest recently. However, there is a fraction of this waste that is not utilized and has uncertain destination, e.g. the non-metallic fraction and the dust generated during metal recovery processes. The focus of this study was to employ the powder generated in the mechanical comminution, granulometric, magnetic and electrostatic separation processes of controller and temperature indicator PCBs of cold rooms to obtain polypropylene (PP) matrix composites with distinct PCBs powder content, 5, 10 and 20% in weight. The sample was collected during the mechanical comminution processes. The materials were weighed, mixed, injection molded and later characterized using tensile tests, Shore D hardness, infrared spectroscopy, thermogravimetric analysis and scanning electron microscopy. Results of the tensile and hardness tests showed properties slightly superior to pure PP, except for strain at break, which was reduced up to 2.7 times for the sample with 20% of residue. In all, the development of composites using the powder of PCBs was considered feasible for applications where tensile strength, stiffness and hardness are important, even for a large amount of residue added (20%).

The aim of this work was to evaluate mass loss in each stage of the recycling process for metal recovery from PCBs of controllers and temperature indicators of cold chambers. The stages of process consists of grinding, particle size classification, magnetic and electrostatic separation. It was analyzed 13 kg of PCBs. These PCBs were crushed and ground. The ground material were subjected to magnetic and electrostatic separator. The losses in the comminution stages were 12.69 % and are lower than those found in other related works that used mixtures of different types of PCBs, whereas in this work only one model plates were analyzed. 27.2 % absolute mass loss we reached out after particle size separation with Tyler Series with 1 mm sieve presents the higher mass losses in the whole process and this fraction was not processed as it results in PCBs powder dust that interferes negatively in the electrostatic separation. Comparing the losses in the stages of shredding of PCBs employed in temperature controllers with other studies involving PCBs from the automotive industry and from computers and cell phones, is remarkable that this type of board presents significantly greater potential to be processed for recovery of its materials.

More and more electronic devices are being produced and most of them are disposed of improperly. In addition, as they contain heavy metals and toxic substances in their composition, the environmental impact increases. This work aims to study the recycling of polymers present in e-waste through the mechanical characterization of polymer blends produced with the main polymers present in printers. To do so, printers were dismounted, the material of the components was classified, and the main polymers were processed. The sample consisted of 20 printers, from which HIPS-90%/PS-10%, HIPS-90%/ABS-10% and HIPS-100%, blends were processed by extrusion and injection of specimens with tensile test geometry. The tensile strength was 39.0 MPa for HIPS/ABS, and 37.5 MPa for HIPS/PS. Despite having slightly different mechanical properties, probably due to possible variations in their chemical composition, the formulations have good quality and potential for use in new products such as hangers, organizing boxes, soles and, watering cans.

In recent years, the inappropriate disposal of polymeric materials has increased due to industrial development and increase of population consumption. This problem may be minimized by using biodegradable polymers, such as bacterial cellulose and poly(hydroxybutyrate), from renewable resources. This work was aimed at monitoring and evaluating degradation of bacterial cellulose, vegetable cellulose and poly(3-hydroxybutyrate) using Thermogravimetric Analysis and Scanning Electron Microscopy. Controlled mass polymer samples were buried in pots containing soil. Samples were removed in 30 day intervals up to 180 days. The results show that the mass of the polymer increased in the first month when in contact with the soil but then it was degraded as evidenced by mass loss and changes on the sample surface.